Created with Sketch. Created with Sketch.

Shop by Category

Bodies & Parts

  • Grille or Mesh Decal #2, All Scales

    This simulated grille also looks like a mesh and it is a decal which requires a solid backing. This is the same pattern as Grille Decal #1, except the pattern is about half the size. Up close, the pattern resembles a chain link fence. This is a...

    $6.95
    Add to Cart
  • Grille or Mesh Decal #1, All Scales

    This simulated grille also looks like a mesh and it is a decal which requires a solid backing. Up close, the pattern resembles a chain link fence. This has a larger pattern then the similar Grille Decal #2. This is a waterslide decal and not a 3D...

    $6.95
    Add to Cart
  • Confederate Flag Set, All Scales

    Confederate Flag Set in five different sizes. This isn't a decal. The flags have adhesive backing. Apply to aluminum foil to make realistic flag Sizes are all square shaped: .62" (16 mm) .47" (12 mm) .35" (9 mm) .15" (4 mm) .12" (3...

    $11.95
    Add to Cart
  • Cross Bones & Skull Flag Set, All Scales

    Skull and Cross Bone flags and symbols in several different sizes. This isn't a decal. The flags have adhesive backing.. Apply to aluminum foil and wrinkle for a realistic flag. Contains: One 1.8" x 1" (45 x 25 mm) two sides flag Two .7"...

    $11.95
    Add to Cart
  • US Flag Set, All Scales

    US Flag Set, 50-Stars, in four different sizes. This isn't a decal. The flags have adhesive backing.. Contains: One 1.5" x .75"  (40 x 20 mm) two sides flag One  .6 x .3" (16 x 8 mm) two-sides flag Three .6 x .3" (16 x 8 mm)...

    $11.95
    Add to Cart
  • Kevlar-Carcon Fiber Decal Sheet #27 1/25

    A decal sheet with a kevlar/carbon fiber pattern. The photo looks black because the pattern is dark and doesn't show well in a photo. The actual decal measures 4.25" x 6.75". One sheet. by SLIXX Decals, 1/25 scale.

    $8.50
    Add to Cart
  • Bumper Brackets 1/25

    A set of two different style brackets to hold up that bumper or other item. Straight brackets with holes. Dropped style bracket. Photos courtesy of Highlight Model Studio Facebook page. Assembly is required.   Photo etched sheet, by...

    $5.45
    Add to Cart
  • Exterior Sun Visor 1/25

    Exterior Sun Visor 1/25

    A visor that mounts above the windshield. Has a perforated pattern and two end brackets. Overall length is 1-1/8" Photo courtesy of Highlight Model Studio Facebook page.   Assembly is required.   Photo etched sheet, by Highlight...

    $5.45
    Add to Cart
  • Rectangle Grille Pattern 1/24-1/25

    This is a plate consisting of a rectangled pattern. It is typically used for a grille, in the place of the kit piece. You can see through it to view your radiator, so make sire it looks realistic with this radiator face detail. It's large enough for a...

    $8.49
    Add to Cart
  • Large Tapered Pro Stock Wing 1/25

    This wing is fairly large and is straighter along the rear edge than along the front edge. End plates are tapered toward the rear and extend down from the top edge. Measurements: Overall length: 2.15" (at the widest, front, edge) Width at end plates:...

    $7.00
    Add to Cart
  • Pro Stock/Pro Mod Wing 1/25

    This wing has a small arch as viewed from the toop. Has teardrop end plates. Measurements: Overall length: 2.15" Width at end plates: .52" Contains 1 resin piece, 1/25 scale

    $7.00
    Add to Cart