Pro Tech 1/16 Scale

Tee Fitting, Small

This is an inline fitting for braided lines, hard lines or hoses.Typical uses are splits for carburetor fuel lines and brake lines.Use Pro Tech .025 Braided Line and matching Fittings. Each package contains one T fitting, by Pro Tech. Metal Cast

Tee Fitting, Large

This is a large inline fitting for braided lines, hard lines or hoses.  Anywhere you have a split.Typical uses are dual feed carburetors, tunnel ram, oil lines and brake lines.Use Pro Tech .035 Braided Line and matching Fittings. Each package...

Braided Line .025 Dia

Depending on your scale, typical uses are fuel, nitrous, oil lines, small heater and coolant hoses and other small transfer lines.The scale size is determined by its outside diameter (OD) compared to real world braided line since an inside diameter isn't...

Braided Line .035 Dia

This .035 diameter braided line equals a scale equivalent 1:1 size of:1/25 scale - 3/4" or -12 AN larger fuel or oil lines.1/16 scale - 3/8" or -6 AN - typically used for smaller fuel or oil plumbing. 1/12 scale - 1/4" or -4 AN...

Hex Braided Line Fittings .025

These hex fittings are compatible with the .025 diameter Braided Line and .020 aluminum hard line.   Make your own AN fittings using Pro Tech's aluminum Hex Fittings. For a realistic anodized appearance on these aluminum fitting, use...

Braided Line .045" Dia

This .045 diameter braided line equals a 1:1 size of:1/25 scale - 1" or -16 AN used for larger fuel or oil lines, larger water transfer lines1/16 scale - 1/2" or 5/8" or -8, -10 AN - typically used for fuel, coolant and oil plumbing. 1/12 scale - 1/4" or...

Hex Braided Line Fittings .035

These hex fittings are compatible with the .035 diameter Braided Line and our .034 and .031 aluminum 'hard' lines found in 'Hard & Soft Lines'.   Make your own AN fittings using Pro Tech's aluminum Hex Fittings. For a realistic anodized...

Braided Line .060" Dia

This .060 diameter braided line scales to the equivalent 1:1 size of:1/25 scale - 1 1/4" or -20 AN - radiator lines, main fuel cell line or other large transfer lines.1/16 scale - 3/4" or -12 AN - typically used for coolant, large fuel delivery or...

Braided Line .080" Dia

This .080 diameter braided line equals the following 1:1 equivalent sizes at each scale:1/25 = 1 3/4" or -28 AN1/16 = 1" to 1 1/4" or -19, -20 AN1/12 = 3/4" or -12 AN1/8 = 1/2" or -8 ANTypical uses are radiator and coolant hoses, large...

5-Point Racing Harness 1/16

5-Point Racing Harness with metal cast buckles and ready to use harness material.Not your flat photo-etched hardware. This is cast for 3D texture and detail. Pro Tech's own design makes it easy to assemble, realistic and beautiful to look at. Can be...

Braided Line .018 Dia

This is the smallest braided line by Pro Tech.Depending on your scale, typical uses are brake lines, small fuel lines like Nitrous, oil lines, gauge and other control lines, etc.The scale size is determined by its outside diameter (OD) compared to real...

Hex Braided Line Fittings .045

These hex fittings are compatible with the .045 diameter Braided Line, .040 Aluminum 'Hard' Line or .039 Soft Line    Make your own AN fittings using Pro Tech's aluminum Hex Fittings.For a realistic anodized appearance on these...

Distributor Kit 1/16

Resin distributor, shaft and boot material. The cap has 'starter' holes to drill out and insert the spark plug boot which is cut from the included material. Refer to the photo showing a completed distributor. Assembly and painting are not included...

Larger Detailing Wire or 1/16 Spark Plug Wire

This black wire can be used for a large gauge electrical wire for 1/25 and 1/16 scales and it's also used for 1/16 scale spark plug wire. This has a solid copper core and will maintain its shape when formed. One package contains 3' of black wire, .024"...

Hex Braided Line Fittings .060

These hex fittings are compatible with the .060 diameter Braided Line and .065 aluminum hard line.   Make your own AN fittings using Pro Tech's aluminum Hex Fittings.For a realistic anodized appearance on these aluminum fitting, use Duplicolor...

Hex Braided Line Fittings .080

These hex fittings are compatible with the .080 diameter Braided Line and .078 aluminum hard line.   Make your own AN fittings using Pro Tech's aluminum Hex Fittings.For a realistic anodized appearance on these aluminum fitting, use Duplicolor...

Blown Engine Fuel Injection Block 1/16

Fuel Injection Block for supercharged engines. This is the fuel block that is located behind the injector hat and behind the blower which feeds the manifold. Use Pro Tech?s .035 Braided Line along with the corresponding fittings for the fuel feed line to...

Throttle Linkage 1/16

Whether it's a blown engine, injected or carbureted, these photoetched pieces will detail your throttle linkage. For the metal linkage that fit into the holes, use the .014 and .020 aluminum lines.  These are stiff enough to hold...

Small Detailing Wire

Small gauge detailing wire for ignition items, lights, gauges and other smaller electrical loads. Available in Black, Blue and Yellow. One package contains 3' x .007" diameter wire. Specify color.

Spark Plug Boots Black 1/16

Rubber boots ready to use as is, for straight boots, or cut them and glue at a 90 degree angle for angled boots.Use in combination with your choice of color Pro Tech Spark Plug Wire.Each pack contains 8 black boots, by Pro Tech.

MSD 6 Ignition Box 1/16

Each package contains 1 MSD 6 ignition box. The casting of this box shows the ribs and area for the MSD logo. The photo shows two Pro Tech MSD boxes with MSD labels copied from an automotive magazine and reduced. These are not included with the MSD 6...

Aluminum Ignition Coil 1/16

Machined aluminum ignition coil with rubber boot.Use with your color choice of Pro Tech Spark Plug Cable.

Rod Ends/Link/Heim Kit 1/16

Cast metal parts for your suspension or throttle linkage detail.  Can be used for heim joints/rod ends in suspension areas like a 4-link rear end, panard bar or front radius rods. Use in combination with Pro Tech's Throttle Linkage kit for a...

Holley Dominator 4bbl Carburetor 1/16

Detailed Holly Dominator 4bbl CarburetorWith single or dual carbs, you'll need Pro Tech's Fuel Junction Block.Also see the Braided Lines, Hard Lines, Soft Lines and Fittings along with the T fitting to split the fuel line to each carb. One per...

Hex Line Fittings .018

These hex fittings can be used for small nuts and are compatible with the .018" diameter Braided Line, . and .020" soft line.   At 1/25 scale, this hex head dimension would represent a 1/4" bolt in real life.   Use these for any small line...

Large Detailing Wire

Large gauge detailing wire for ignition items, batteries and other items that have large electrical loads. Available in Black, Red, Blue and Yellow. One package contains 3' x .018" diameter wire. Specify color.

Mallory/MSD Ignition Coil 1/16

Modeled after a Mallory Ignition Coil. Also looks very similar to a MSD Ignition Coil. Photo of completed piece is for reference only. Painting, wires and decals are not included. Each package contains 1 coil. Resin 

Roll Bar Padding 1/16

Rubber tubing for roll bars.Can also be used for other larger water/coolant hoses.At 1/16 scale, this would be equal to 1.5" ID and 3.5" OD.At 1/12 scale, this would be equal to 1.25". ID and 2.5" OD.Black.

Carburetor Fuel Junction Block 1/16

For your single or dual carburetor setups.  Made with molded-on fittings.Use .035 Braided Lines and Fittings and large T fitting. Each package contains 1 Fuel Junction Block, by Pro Tech. Resin cast

Barrel Valve 1/16

A barrel valve is located on the left side of a supercharged engine injector hat. The fuel input is via a braided line from the fuel pump and 2 outlet braided lines go to 2 fuel junction blocks (see ENGINE DETAILING).Designed for Pro Tech .035 Braided...

Drag Racing Parachute 1/16

Detailed Drag parachute.One per package.Resin

Dual Remote Oil Filter 1/16

Each package contains 1 adapter and 2 oil filters.   See the Braided Lines and Fittings to complete the plumbing of the oil lines. Adapter is metal cast and can be polished.  Filters are machined aluminum   

Aluminum Gas Cap 1/16

Excellent detail for your race car fuel cell, hot rod Moon tank and other tanks like an oil tank on a Funny Car, Pro Mod or Dragster.Can also be used for a radiator cap, engine oil breather cap or other instance where a filler neck is required. Diameter...

Aluminum Oil Filter 1/16

Each package contains 1 filter. Machined aluminum  

Drag Racing Full Face Helmet 1/16

Detailed Full Face Helmet. Ready for your custom paint design.  Looks right at home on the cockpit seat or the hood of that Pro Mod car. One per package. Resin

Barry Grant DEMON 4bbl Carburetor 1/16

Detailed Barry Grant 4bbl CarburetorWith single or dual carbs, you'll need Pro Tech's 1/16 scale Fuel Junction Block.Also see the Braided Lines, Hard Lines, Soft Lines and Fittings along with the T fitting to split the fuel line to each carb. One...