1/25 - 1/24 Scale

Spark Plug Wire, Lt. Blue .012” 1/24-1/25

A light blue spark plug wire equal in size to a real world 8mm wire. 7mm, 8mm and 9mm spark plug wires are the most common. Can also be used for larger electrical loads. Bends easily and holds its shape.Also available in the following...

Spark Plug Wire, Red .012” 1/24-1/25

A red spark plug wire equal in size to a real world 8mm wire. 7mm, 8mm and 9mm spark plug wires are the most common. Can also be used for larger electrical loads. Bends easily and holds its shape.Also available in the following...

Plastic Barrel 55 Gal - 200L, 1/24-1/25

Here's the perfect detailing item for a diorama or the bed of a truck. This plastic barrel represents a standard 55 gallon / 200L container. The barrel is comprised of two haves plus the top and bottom. Check out this small decal sheet for adding...

Soft Line - Red .012", .30mm OD

This is a small, solid, flexible, deep red line.  It can bend at a fairly sharp angle without kinking.See Size A1 Ferrules for this soft line. This soft line equals the following equivalent 1:1 size at each scale.1/25 scale = 5/16"1/16 scale...

'55 Chevy Headlight, Taillight, Trim Pieces, 1/25

Need replacement exterior trim parts for your '55 Chevy? Refer to photo of parts to compare with below list. CHROME PARTS: Headlight bezels (without clear lenses)TaillightsFront running light/turn signal lightsHood tip 'flying' emblem1 Body/Hood...

Home Depot Pre-Painted Kit #20 Tony Stewart NASCAR 1/24

This is a kit and not a 'snap' type model. Includes glue and opening hood. Features highly detailed chassis and engine. Home Depot's #20 Monte Carlo driven by Tony Stewart. Features a driver figure with a full helmet. Box is unopened, sealed and new...

Sander Engineering 750 Rear Wheels 1/25

A pair of Sander 750 Series rear wheels In 1/25 scale. Includes: Deep Outer Rims Inner and Outer Center Inserts Instructions  Wheel dimensions:Width .730"Outside Diameter .730" Here's a real world Sander Eng 750 rear...

Ring Terminals, 1/25

Here is a detailing item to fasten cable, chain, rope, etc to an object. Use these for cable ends on a wrecker or 4X4 pickup winch for example. Glue the cable into the open end of the terminal tube and then use small bolts to fasten the terminal to...

Chevy 409 Blown Engine 1/25

A blown Chevy 409 engine. A Revell kit engine from a '55 Chevy. Items Included Block (3-pieces)HeadsOil pan409 chrome valve coversChrome BlowerChrome timing coverBlower belt with pulleysChrome Inline injectorsBellhousingTransmissionStarterDrop...

Summit / GXP Decal Sheet, 1/25

The scalloped flame design can be used on any car, but it is modeled after Jason Line’s Summit Pontiac GXP. Includes the Summit ‘S’ for the roof, body-side decals, front grilles and headlights. You will also need this decal...

Pro Stock Late Model Seat, 1/24

Here is a one-piece ‘shell’ type seat. Has molded-in padding, harness and buckles. Measurements: Width at Top (widest point) - 0.82” Height - 1.15” Depth - 0.50” One resin seat, by Comp Resins, 1/24 scale.  

‘72-‘73 Vega P/S (Grumpy) Body 1/25

Build it as your own racer or duplicate a ‘72-‘73 Bill “Grumpy” Jenkins’ P/S Vega. A chassis & interior kit is available here but see the BUNDLE DEAL below. Features Pro Stock Vega Body Hood with Scoop Grill...