Created with Sketch. Created with Sketch.

Shop by Category

Futurattraction 1/25 Scale

fa-logo.jpg1/25 SCALE ONLY 

 

Tips for dealing with photo etch - removal from rubber backing:

Soak light-weight or fragile pieces in acetone until the part separates from the rubber backing.  For heavier parts that have no etch lines or thin edges where there is a likelihood of damage, you may be able to peel the rubber off before soaking in acetone.  It works best to fold the rubber back against itself as you peel it back to lessen the likelihood being parts.

  • Cragar SuperTrick Wheels 4-Set, Spindle 1/25

    A highly detailed set of front and rear Cragar Super Trick wheelsThese Cragar's replicate 15" wheels used on 1960s-80s era drag cars.  Crowned centers are present on both front and rear wheels, with double-drilled pattern on rear wheels.Front wheels...

    $10.00
    Add to Cart
  • Starlite Rear Wheels 1/24

    A new custom wheel design by Futurattraction.  These match Futurattraction's front spindle-mount wheels   They are the same 5-point star design and can also use a color-coordinated (front or rear half) paint scheme. Includes: CNC...

    $30.00
    Add to Cart
  • Starlite Front Wheels 1/24

    A new custom wheel design by Futurattraction.  These are spindle-mount wheels and fit Futurattraction's' spindle front strut kit.    They are a simple 5-point star design, but have a significantly thinner "show side" wheel half...

    $20.00
    Add to Cart
  • Billet Specialties Comp7 Front Wheels 1/25

    A pair of Billet Specialties COMP7 front wheels.Includes: Outer Rims Inner and Outer Center Inserts Hubs Instructions   Photo of real world Comp7 wheel   Wheel dimensions:Width .200"Outside Diameter .0600"   Matching rear...

    $20.00
    Add to Cart
  • Shown with an optional beadlock ring

    Billet Specialties Comp7 Rear Wheels 1/25

    A pair of Billet Specialties COMP7 rear wheels.Includes: Deep Outer Rims Inner and Outer Center Inserts Instructions   Wheel dimensions:Width .730"Outside Diameter .730"   Left wheel below had the optional bead lock ring and back...

    $30.00
    Add to Cart
  • Brake Kit - Rear .126" Rotor ID 1/25

    This is the same rear end brake set as Futurattraction's FA-C-ROT-DR2R, except this rotor has a larger .126" ID hole. This allows for the hubs and rotors to slide over Futurattraction's axle housing and gives more gluing surface where they are adjacent...

    $5.00
    Add to Cart
  • Hurst Shifter Set 1/25

    This iconic shifter was THE shifter for drag racing, muscle cars, gassers and street machines in the '60's. Includes 3 different arms and shifter linkage. You'll find various shifter knobs here.          Photo etched...

    $4.00
    Add to Cart
  • Rear End Carrier Section

    Rear End Carrier Section

    Here is carrier or 'pumpkin' section for a Fabricated rear, street rod rear or 9" rear end. Add a little more detail to that kit rear end by substituting the carrier with this one.   One resin part, by Futurattraction, 1/25 scale.

    $2.00
    Add to Cart
  • American Trak Star Rear Wheels 1/25

    American Racing TrakStar Rear Wheels  Brand new and I only have a limited quantity to start with. These American Racing rear wheels match the Trak Star front wheels. Here's a  photo of the real wheel with a beadlock ring. Includes: Deep Outer...

    $30.00
    Add to Cart
  • Weld V-Series Front Wheels 1/25

    A pair of Weld V-Series front wheels to match the VSE rear wheels.Includes: CNC Aluminum Rings 2-Piece PE Centers Instructions  These are hub-style mount wheels, NOT spindle mount.            Photo of real...

    $20.00
    Add to Cart
  • Aluminum Wheel Spindle Front Strut Kit 1/25

    This strut front end kit is similar to the original Strut kit, but incorporates a modified spindle to accommodate the .094" ID of the spindle cap/boss used on Futurattraction aluminum front wheels with photo etch centers, along with revised...

    $18.00
    Add to Cart
  • Spark Plug Wire Loom Set 1/25

    A nice set of photo etched wire looms. Spreaders are in 2, 3 and 4-hole configurations. If using soft .020" (or smaller) rubber wires, use the looms as they are. If using solid wire, It is necessary to "clean up" the holes with a .020" bit so wires will...

    $5.00
    Add to Cart
  • Shown Assembled Parts Included

    Rectangular Frame Rails 1/24-1/25

    This rear frame rail replicates a mandrel bent rectangular in a 2"x 3" size. Dimensions: Rails are .125" x .080" Cross members are 060" diameter Total length is 2.6"   The rails are 3D printed in Shapeways' Frosted Ultimate...

    $8.00
    Add to Cart
  • Real World Crank Trigger

    Big Block Ford, Crank Trigger 1/25

    For that big block Ford engine to keep perfect ignition timing. Includes crank trigger wheel, sensor mount and adjustable sensor mounting bracket. A crank triggered ignition system can make more horsepower than a distributor triggered system. A crank...

    $2.00
    Add to Cart
  • BBC Centered Motor Plate 1/25

    A more accurate motor plate than found in a kit. It is designed for those cars with a centered driveline.While this motor plate is copied after the one used in the Revell Pro-Sportsman kits, it can be used in any build with possible modification.It is...

    $4.00
    Add to Cart
  • Drag Slicks,17x36x16 1/25

    These Drag Slicks equal a scale 17x36-16 tire.  This is representative of a current Pro Mod, FC or TF drag slick. Dimensions:Overall Width = .85"Diameter = 1.46"Tread Width = .70"Wheel Opening =.715" The tire ID is designed to work with earlier...

    $10.00
    Add to Cart
  • Lever Latch 5-Way Racing Harness 1/25

    The origins of this style racing harness hardware dates back to WWII.  It is still available and widely in use today.  These 1/25th scale sets replicate the basic style of hardware used by many race and street cars, even today.  Etched...

    $8.00
    Add to Cart
  • Shown with optional beadlock rings

    Weld Delta 1 Rear Wheels 1/25

    A pair of Weld Delta 1 rear wheels. These are one-piece CNC machined aluminum wheels. Includes: CNC Aluminum Rings PE Centers Instructions    PHOTO OF REAL DELTA 1 WHEEL WITH A BEADLOCK RING (not included) Wheel dimensions:Width ...

    $36.00
    Add to Cart
  • Billet Specialties Comp5 Front Wheels 1/25

    A pair of Billet Specialties front wheels.Includes: Outer Rims Inner and Outer Center Inserts Hubs Instructions A Front Strut spindle kit is available for these wheels.  The nose of the spindle is designed to center in the spindle...

    $20.00
    Add to Cart
  • Billet Specialties Comp5 Rear Wheels 1/25

    A pair of Billet Specialties rear wheels.Includes: Deep Outer Rims Inner and Outer Center Inserts Instructions   Wheel dimensions:Width .730"Outside Diameter .730"   Matching front wheels are also available.  1/25 scale, by...

    $30.00
    Add to Cart
  • Weld Magnum Rear Wheels 1/25

    A pair of Weld Magnum rear wheels.Includes: Deep Outer Rims Inner and Outer Center Inserts Instructions    Wheel dimensions:Width .730"Outside Diameter .730"    Matching front wheels are also available.   1/25 scale, by...

    $30.00
    Add to Cart
  • Weld Magnum Front Wheels 1/25

    A pair of Weld Magnum front wheels.Includes: Outer Rims Inner and Outer Center Inserts Hubs Instructions A Front Strut spindle kit is available for these wheels.  The nose of the spindle is designed to center in the spindle...

    $20.00
    Add to Cart
  • Shown with optional beadlock ring

    Weld V-Series Rear Wheels 1/25

    A pair of Weld V-Series rear wheels.Includes: Deep Outer Rims Inner and Outer Center Inserts Instructions Wheel dimensions:Width .730"Outside Diameter .730" Product photo shows a beadlock ring that is not icnluded.    1/25 scale, by...

    $30.00
    Add to Cart