Pro Tech 1/25 Scale

MSD Pro Mag 44 Pre-Wired 1/25

Here's a 3D-printed MSD Pro Mag with your color choice of spark plug wire already installed.Drill a hole in your block and insert this MSD magneto. Route the wires to the spark plugs and don't forget the Spark Plug Boots, for even more detail. Specify...

Spark Plug Boots 90Deg, 3D, 1/25

A package of ten, 90-degree, 3D-printed, spark plug boots, ideally suited for the distributor cap (see photo). Enough for eight spark plugs boots at the distributor, plus two boots for the coil wire.  You will need another set of boots for the...

Spark Plug Boots 45Deg, 3D, 1/25

A package of ten, 45-degree, 3D-printed, spark plug boots.   When cutting the boot from the tree, a stem remains to insert into the head's spark plug hole (use a #70 drill bit).   The hollow end accepts Pro Tech's Spark Plug Wire. Pro...

3D-Printed 4bbl Carburetor 1/25

Highly detailed Holley Street/Strip 4-bbl Carburetor.With single or dual carbs, you'll need a Fuel Junction Block (see 1/25 SCALE/ENGINE RELATED/FUEL MANAGEMENT). Also see the Braided Lines, Hard Lines, Soft Lines and Fittings along with the SMALL or...

Aluminum Distributor Body 1/25

This is the same Pro Tech distributor body used in their pre-wired distributors. This is the body without the spark plug wires.  You may have your own wires you want to use. A hole is provided in the top.   Contains 1 machined aluminum...

Electric Fuel Pump & Filter 1/25

An electric fuel pump with a fuel filter similar to the MagnaFuel pump.     Here's a photo of the real thing     One resin piece, by Pro Tech, 1/25 scale.    

Hex Braided Line Fittings .025

These hex fittings are compatible with the .025 diameter Braided Line and .020 aluminum hard line.   Make your own AN fittings using Pro Tech's aluminum Hex Fittings. For a realistic anodized appearance on these aluminum fitting, use...

Braided Line .080" Dia

This .080 diameter braided line equals the following 1:1 equivalent sizes at each scale:1/25 = 1 3/4" or -28 AN1/16 = 1" to 1 1/4" or -19, -20 AN1/12 = 3/4" or -12 AN1/8 = 1/2" or -8 ANTypical uses are radiator and coolant hoses, large...

Braided Line .045" Dia

This .045 diameter braided line equals a 1:1 size of:1/25 scale - 1" or -16 AN used for larger fuel or oil lines, larger water transfer lines1/16 scale - 1/2" or 5/8" or -8, -10 AN - typically used for fuel, coolant and oil plumbing. 1/12 scale - 1/4" or...

Braided Line .035 Dia

This .035 diameter braided line equals a scale equivalent 1:1 size of:1/25 scale - 3/4" or -12 AN larger fuel or oil lines.1/16 scale - 3/8" or -6 AN - typically used for smaller fuel or oil plumbing. 1/12 scale - 1/4" or -4 AN...

Braided Line .025 Dia

Depending on your scale, typical uses are fuel, nitrous, oil lines, small heater and coolant hoses and other small transfer lines.The scale size is determined by its outside diameter (OD) compared to real world braided line since an inside diameter isn't...

Braided Line .018 Dia

This is the smallest braided line by Pro Tech.Depending on your scale, typical uses are brake lines, small fuel lines like Nitrous, oil lines, gauge and other control lines, etc.The scale size is determined by its outside diameter (OD) compared to real...