Quick view Front Suspension & Engine Mount Kit, Brass 1/25 There are enough parts included for two cars. Includes two front motor mount plates - one solid and one drilled. The photo below is a 1/16 scale 'work-in-progress' by Clay Kemp. It shows the use of brass pieces from this set, the... $4.95 Add to Cart Compare
Quick view Holley Dominator 4bbl Carburetor 1/16 Detailed Holly Dominator 4bbl CarburetorWith single or dual carbs, you'll need Pro Tech's Fuel Junction Block.Also see the Braided Lines, Hard Lines, Soft Lines and Fittings along with the T fitting to split the fuel line to each carb. One per... $2.75 Add to Cart Compare
Quick view Barrel Valve 1/16 A barrel valve is located on the left side of a supercharged engine injector hat. The fuel input is via a braided line from the fuel pump and 2 outlet braided lines go to 2 fuel junction blocks (see ENGINE DETAILING).Designed for Pro Tech .035 Braided... $2.75 Add to Cart Compare
Quick view Rod Ends/Link/Heim Kit 1/16 Cast metal parts for your suspension or throttle linkage detail. Can be used for heim joints/rod ends in suspension areas like a 4-link rear end, panard bar or front radius rods. Use in combination with Pro Tech's Throttle Linkage kit for a... $2.75 Add to Cart Compare
Quick view Roll Bar Padding 1/16 Rubber tubing for roll bars.Can also be used for other larger water/coolant hoses.At 1/16 scale, this would be equal to 1.5" ID and 3.5" OD.At 1/12 scale, this would be equal to 1.25". ID and 2.5" OD.Black. $3.75 Add to Cart Compare
Quick view Mallory/MSD Ignition Coil 1/16 Modeled after a Mallory Ignition Coil. Also looks very similar to a MSD Ignition Coil. Photo of completed piece is for reference only. Painting, wires and decals are not included. Each package contains 1 coil. Resin $2.75 Add to Cart Compare
Quick view Brake or Fuel Line .016", .4mm Dia This hard line equals the following equivalent 1:1 size at each scale. 1/25 scale = 3/8"1/16 scale = 1/4"1/12 scale = 3/16"1/8 scale = 1/8" Depending on your scale, typical uses are injector lines from distribution blocks into a... $3.50 Add to Cart Compare
Quick view 00-90 Washers This is a flat washer to fit a 00-90 screw. Perfect for detailing your suspension or wheels as lug nuts. The metal finish is realistic looking compared to brass nuts. And no painting is required.Use in suspension parts like 4-link... $2.75 More Coming Compare
Quick view Drag Racing Full Face Helmet 1/16 Detailed Full Face Helmet. Ready for your custom paint design. Looks right at home on the cockpit seat or the hood of that Pro Mod car. One per package. Resin $2.75 Add to Cart Compare
Quick view Cockpit Interior Set, Funny Car, Top Fuel 1/16 Here is a pair of butterfly steering wheels for your Funny Car or Top Fuel racer. Enough for two cars. Includes grips for the handles plus four (4) small levers that can be used for a parachute release or other. NOTE: The steering wheel is made so that... $8.00 More Coming Compare
Quick view Pedal Set for FC, PM or Door Slammer 1/16 You need a set of these pedels to complete that racing interior and sdd realism and detail to your build. Contains one each: Accelerator pedal Brake pedal Clutch pedal Pedal foot pads Make sure you click on the photo, to enlarge... $6.00 Add to Cart Compare
Quick view Front Suspension & Engine Mount Kit, Brass 1/16 There are enough parts included for two cars. Includes two front motor mount plates - one solid and one drilled. The photo below is a work-in-progress by Clay Kemp. It shows the use of brass pieces from this set, the Dirt... $4.95 Add to Cart Compare
