1/25 - 1/24 Scale

Spark Plug Boots 90-Deg, 3D, 1/25

A package of nine, black, 90-degree, 3D-printed spark plug boots. Paint them your desired color. Enough for eight spark plugs boots at the distributor, plus one boot for the coil wire.  You will need another set of boots for the spark plugs at...

MSD Pro Mag 44 #1, 1/25

A 3D-printed MSD Pro Mag 44 with a decal. It consists of three pieces - Body, Cap and Cover, to make it easy to run the wires through. An MSD decal is included but not shown in the photos. The ignition wires pass through the openings of the cap. Cut...

Auto/Race Car Trailer - 2 Versions, 1/25

A great accompaniment for a drag or race car push-car or diorama. This trailer can be made with the tire rack or without it. It is made for a plastic model, not die cast. Includes: Ramps (stowable)Tire rack and sidesTwo trailer jacksAdjustable wheel...

Ignition or General Wire, Yellow .0194"

This wire can be used for many heavier electrical loads. Scale Motorsport's wire is not as stiff as most other electrical wires. It is .0194" diameter which is equal in real life to just under 1/2" or 12mm at 1/25 scale. At 1/16 scale, this wire would...

Ignition or General Wire, Light Blue .0194"

This wire can be used for many heavier electrical loads. Scale Motorsport's wire is not as stiff as most other electrical wires. It is .0194" diameter which is equal in real life to just under 1/2" or 12mm at 1/25 scale. At 1/16 scale, this wire would...

Ignition or General Wire, Red .0194"

This wire can be used for many heavier electrical loads. Scale Motorsport's wire is not as stiff as most other electrical wires. It is .0194" diameter which is equal in real life to just under 1/2" or 12mm at 1/25 scale. At 1/16 scale, this wire would...

Ignition or General Wire, Orange .0126”

This wire can be used for many electrical loads. Scale Motorsport's wire is not as stiff as most other electrical wires. It is .0126" diameter which is equal in real life to slightly larger than 5/16" or 9mm at 1/25 scale. At 1/16 scale, this wire...

MSD Pro Mag 44 with Dual Drive, 1/25

A 3D-printed MSD Pro Mag and a Drive to add a second mag. It consists of three pieces - Body, Cap and Cover. A MSD decal is included but not shown in the photos. The ignition wires pass through the openings of the cap. Make the wires long enough to...

DART BBC Tunnel Ram Engine 1/25

A 3D-printed Dry Sump BBC engine based on a DART Billet engine. Features: Detailed Block Enlarged Heads Tunnel Ram Manifold Two Demon Carbs Distributor Tall 'DART' valve covers Timing Cover, Water Pump & Alternator Rubber Fan Belt Oil...

DART BBC Tunnel Ram Dry-Sump Engine 1/25

A 3D-printed Dry Sump BBC engine based on a DART Billet engine. Oil pan and external oil pump are pre-drilled for hoses/fittings. Strip end off Braided Line and insert core into hole.Harmonic Balancer and oil pump will accept 1mm diameter pulley shafts...

Round Air Cleaner, Low-Profile, Spun Aluminum 1/25

Very nice looking air Cleaner, 5/8" diameter x 5/32" high Spun Aluminum. Polished with slight peak in top center. Includes mesh around air cleaner. It has a flat bottom. This is a typical wide, low profile air cleaner. One complete aluminum piece by...

Round Air Cleaners, High-Profile, Spun Aluminum 1/25

Very nice looking air Cleaner, 9/16" diameter x 7/32" high Spun Aluminum. Polished with slight peak in top center. Includes mesh around air cleaner. It has a flat bottom. This is fairly high, so check for hood clearance. One complete aluminum piece...