1/16 Scale

671 GMC Blower 1/16

A 671 blower for early dragsters or for a street machine.Blower pulley is attached to the front plate.The detail is quite good and the bolts are sharp. Check out this photo for an idea of which blower you need. Contains 2 resin pieces.

Throttle Return Spring, 1/16

A small spring to simulate a throttle return spring. This is a pretty tight spring which would have the throttle in a closed position. Made of stainless steel and measures .07" OD x .25" long. Contains a loop on one end and can be cut to length...

M&H Racemaster Drag Slicks 1/16

M&H Racemaster Drag Slicks. Raised 'M&H Racemaster' on sidewall. These are a hard resin and do not have a lot of room for play with wheel sizes. Tire Measurements: Width 1.00",  25.4mmDiameter. 2.00", 50.8mmWheel opening 1...

Ignition or General Wire, Yellow .0194"

This wire can be used for many heavier electrical loads. Scale Motorsport's wire is not as stiff as most other electrical wires. It is .0194" diameter which is equal in real life to just under 1/2" or 12mm at 1/25 scale. At 1/16 scale, this wire would...

Ignition or General Wire, Light Blue .0194"

This wire can be used for many heavier electrical loads. Scale Motorsport's wire is not as stiff as most other electrical wires. It is .0194" diameter which is equal in real life to just under 1/2" or 12mm at 1/25 scale. At 1/16 scale, this wire would...

Ignition or General Wire, Red .0194"

This wire can be used for many heavier electrical loads. Scale Motorsport's wire is not as stiff as most other electrical wires. It is .0194" diameter which is equal in real life to just under 1/2" or 12mm at 1/25 scale. At 1/16 scale, this wire would...

Ignition or General Wire, Orange .0126”

This wire can be used for many electrical loads. Scale Motorsport's wire is not as stiff as most other electrical wires. It is .0126" diameter which is equal in real life to slightly larger than 5/16" or 9mm at 1/25 scale. At 1/16 scale, this wire...

Weld V-Series Aluminum Rear Wheels 1/16

A detailed pair of Weld V-Series aluminum rear wheels In 1/16 scale. These match Futurattraction's V-Series front wheels.  These replicate Weld's 16" x 16" wheels. Three different inserts stack to create a 3-dimentional look. The beadlock...

Weld V-Series Front Wheels, 1/16

A pair of  Weld's V-Series 15" x 3.5" spindle-mounted front wheel. Includes three .20" thick 6061-T1 aluminum center inserts that stack for a 3-dimentional look. The outer-most insert is slightly smaller to represent the 'stepped' look. Also...

Weld Magnum Aluminum Rear Wheels 1/16

A detailed pair of Weld Magnum aluminum rear wheels In 1/16 scale. These match Futurattraction's Magnum front wheels.  These replicate Weld's 16" x 16" wheels. Three different inserts stack to create a 3-dimentional look. The beadlock rings...

Weld Magnum Front Wheels, 1/16

A pair of  Weld's Magnum 15" x 3.5" spindle-mounted front wheel. Includes three .20" thick 6061-T1 aluminum center inserts that stack for a 3-dimentional look. The outer-most insert is slightly smaller to represent the 'stepped' look. Also...

Billet Specialties CO7 Aluminum Front Wheels, 1/16

Here is Billet Specialties' Comp7 15" x 3.5" spindle-mounted front wheel. Includes three .20" thick 6061-T1 aluminum center inserts that stack for a 3-dimentional look. Also includes spindle caps. These will fit Futurattraction's 1/16 scale Front...