1/25 - 1/24 Scale

Weld AlumaStar Rear Wheels 1/25

A pair of Weld AlumaStar rear wheels In 1/25 scale. Includes: Deep Outer Rims Inner and Outer Center Inserts Instructions Matching front wheels are also available. Note the difference between the 1/24 version (left) and the 1/25 version...

Chevy 1966 Pickup Detail Kit 1/25

A detail set for Revell's 1966 Chevy Pickup Truck.  Includes: Cab trim pieces behind the door C10 logo Steering wheel horn ring Rear tail lights Keys     Here's a kit that you may like.   Photo etched sheet, by...

Pedals - Drag, Rat Rod, Hot Rod 1/25

A set of pedals, perfect for dragster, gasser, hot rod, rat rod or other project car. Nine sets of pedals are included. Each set has accelerator, brake and clutch pedals. Photo etched and assembly is required.   Photo etched sheet, by Highlight...

Pro Mod / Funny Car / Pro Stock Rear Wing 1/25

Includes main horizontal wing, sides and support rods. This wing can be made to fit many different race classes.   Here are some examples of what can be done.     Resin, 1/25 scale

Fenton/Anson Front Wheels 1/25

A pair of 5-slot Fenton (or Anson) front wheels. Popular on gassers, super stock or pro stock cars. These are similar to the Gasser Front Wheels, but these have larger slots  OD = .67", 17mm Overall Width = .19", 5mm   The wheels that will...

Weld V-Series Rear Wheels 1/24

A pair of Weld V-Series rear wheels.Includes: Deep Outer Rims Inner and Outer Center Inserts Instructions Wheel dimensions:Width .730"Outside Diameter .730" Note the difference between the 1/24 version (left) and the 1/25 version (right) below...

Cragar 15" SuperTrick Wheels 4-Set, Hub 1/24

A highly detailed set of front and rear Cragar Super Trick wheelsThese Cragar's replicate 15" wheels used on 1970s-80s era drag cars.  Crowned centers are present on both front and rear wheels, with double-drilled pattern on rear wheels. Inner and...

Good Year Polyglas Tire Set of 4 1/25

A set of four Good Year Polyglas blackwall tires with white lettering on both sides. The tread detail is excellent. Two sizes are included - F60-15 for the front and L60-15 for the rear. These tires were popular during the '60's and '70's and are a...

Blower Restraint Plate, 1/25

This restraint plate sits under the blower and restraint straps would fasten to the slots and go over the blower to hold it down in the event it would blow up. It is universal to all blowers. This photo etched piece is etched out of .006" nickel-silver...

70's Pro Stock Front Tires - Firestone Drag 500 / Goodyear, 1/25

These front tires will work for a Gasser as well as a Pro Mod or street racer.   Has Firestone Drag 500 & Goodyear MarkingsCast from Medium Soft Rubber These are semi hard tires but still flexible. Measurements:Outside Diameter = .1...

Rear Tube Frame/Clip .700" Wide 1/25

Here's  a round-tube rear frame clip ready to install.  It's 3D printed in FUD material (see below). Dimensions are:Frame width = .700" (about 45/64", 17.8mm)Frame tube diameter = .080"Cross member diameter = .063"Overall length = 2.55" Two...

Small Multi-Use Springs, Throttle/Hood/Brake (pair)

Two small springs for throttle linkage or to hold those semi tractor air hoses.Depending on your scale, these could be used for brake pad springs or hood-hinge springs.Spring length is .25"Contains two (2) steel springs, compression type, by Model Car...