1/25 - 1/24 Scale

P/M-P/S '70.5 Camaro Tubular Chassis 4-1/2" Wheelbase, 1/25

A complete one-piece 3D-resin-printed chassis. This was designed for a '70.5 Pro Mod Camaro, but the body is no longer being made. See dimensions in the drawings above. This particular chassis has a long nose, forward sloping roof, firewall and wheel...

Soft Clear Line - Tube .039, 1mm OD, .020" ID

This is a soft, clear line that bends easily and smoothly.  It's able to bend at a sharp angle without kinking. It is a hollow tube with a .020" ID.See .040" Hex Fittings or Size C (or Size D for more space) Ferrules for hose ends.This clear line...

Billet style Hood-Side Louvers 1/25

Four pairs of open louvers to let some of the engine heat out. The finish is shiny and the slot openings are clean. Cut out a piece of the hood side and cover it with these louvers. You'll be able to see right into the engine bay. Or see out with the...

Engine Detailing Set 1/25

This photo etched set has items for a drag machine as well as a street machine. Photo etched plate contains: Blower starter brackets Distributor and magneto plates Spark plug wire looms By Model Car Garage, 1/25 scale.

3-Drawer Tool Box, 1/25

A small tool box to hold the tool set by Highlight Model Studio. It actually has three separate drawers. Instructions are not included, so look at the photo of the completed box for direction. Includes two photo etched sheets for the box,...

Ignition or General Wire, Orange .0126”

This wire can be used for many electrical loads. Scale Motorsport's wire is not as stiff as most other electrical wires. It is .0126" diameter which is equal in real life to slightly larger than 5/16" or 9mm at 1/25 scale. At 1/16 scale, this wire...

DART BBC Tunnel Ram Dry-Sump Engine 1/25

A 3D-printed Dry Sump BBC engine based on a DART Billet engine. Oil pan and external oil pump are pre-drilled for hoses/fittings. Strip end off Braided Line and insert core into hole.Harmonic Balancer and oil pump will accept 1mm diameter pulley shafts...

Round Air Cleaners, High-Profile, Spun Aluminum 1/25

Very nice looking air Cleaner, 9/16" diameter x 7/32" high Spun Aluminum. Polished with slight peak in top center. Includes mesh around air cleaner. It has a flat bottom. This is fairly high, so check for hood clearance. One complete aluminum piece...

Spoiler Wing 1/25

A nicely made photo etched rear spoiler wing. Mount this on the top of a semi truck cab, the back of a street machine or on a race car. DIMENSIONS: Width = 2-3/16" WideDepth = 5/8"Height = 7/16" Assembly required.  Photo etched sheet, by...

Mud Flaps or Anti-Sail Weights 4-Pair 1/24-1/25

A set of photo etched weights to keep big rig mud flats from sailing. Can also be mounted behind pickup rear tires. Contains enough for 8 wheels. They can be painted or left 'bare' for that aluminum or chrome look.   By Detail Master, 1/25...

Pinpoint Glue & Weathering Brushes 3-Set

Three long-reach pinpoint brushes with a easy-grip end. Besides using these for Plastic Magic liquid glue, use them for brushing off unwanted Photo Etch glue. Three brushes, by Deluxe Materials

Pin Flow Applicator for Liquid The Glue

For a precise, small application using a needle-tip for no glue runs. I've tried needle-type glue applicators in the past and the problem was that the CA glue would clog before I applied it. Now here is an applicator that works with liquid glue made for...