Fenton/Anson Front Wheels 1/25

A pair of 5-slot Fenton (or Anson) front wheels. Popular on gassers, super stock or pro stock cars. These are similar to the Gasser Front Wheels, but these have larger slots  OD = .67", 17mm Overall Width = .19", 5mm   The wheels that will...

Wide Rear Steel Wheel Pair 1/25

A pair of deep rear wheels. These are stock looking steel wheels with lug nuts, except they're wide to hold big rubber. Great for street racers, early Super Stock or Pro Stock and Rat Rods. Width/Depth = .33" (11/32")   Contains 2 resin wheels by...

Dual Quad Tunnel Ram Manifold 1/25

Set a pair of Dominator or Demon carbs on top of this manifold. Make sure you have room under your hood or cut a hole in the hood to allow for the height. Overall height is .43" (7/16"). Here's a photo of a real dual quad setup byRich Vitiritti. ...

S.C.O.T Blower 1/25

Here's a special blower for that Flathead engine. S.Co.T. is an abbreviation for 'Supercharger Company of Turin' (Torino), Italy. It was one of the most popular "roots" style blowers in the 1950's and popular today on Street Rods and Rat Rods...

Holley Dominator Carburetor (Pair) 1/25

A pair of nicely detailed Holly Dominator 4-bbl Carburetors. With single or dual carbs, you'll need a Fuel Junction Block (see ENGINE DETAILING). Also see the Braided Lines, Hard Lines, Soft Lines and Fittings along with the SMALL or LARGE 'T' fitting...

GM TH350 3-Speed Transmission 1/25

A nicely detailed General Motors 350 Turbo Hydromatic transmission. Molded in one piece with bellhousing. By Competition Resins, 1/25 scale

Pirelli Type Small Front Racing Tires 1/25

These front tires will work for a Gasser as well as a Pro Mod or street racer. These are slightly smaller than the Futurattraction Front Runner tires. These are semi hard tires but still flexible. Measurements:Outside Diameter = .98"Overall width = ...

Good Year Dragster Slicks 1/25

These are labeled '60's Goodyear Dragster Slicks but depending on the size you want, these will work for any racer. "Good Year" is in raised letters on both sides. These are slightly smaller than the Comp Resins' Pro Stock slicks. These are fairly...

Black Coated Hard Line .080", 2.05mm Dia

A glossy black hard line that holds its shape and doesn't kink at tight angles. This hard line equals the following equivalent 1:1 size at each scale.1/25 scale = 2"1/16 scale = 1 1/4"1/12 scale = 1"1/8 scale  = 5/8"Use Pro Tech Fittings sized...

Black Coated Hard Line .050", 1.29mm Dia

A glossy black coating over a wire will give a different look to your lines. This hard line will hold the bend you want and not kink. Equivalent 1:1 size at each scale.1/25 scale = 1 1/4"1/16 scale = 3/4"1/12 scale = 7/16"1/8 scale   = 3/8"Depending...

Black Coated Hard Line .098", 2.5mm Dia

Here is a glossy black hard line that holds its shape and doesn't kink at tight angles. This is has a solid copper core that makes it pretty stiff. This hard line equals the following equivalent 1:1 size at each scale. 1/25 scale = 2 1/2" 1/16...

Black Coated Hard Line .032", .81mm Dia

This hard line has a glossy black coating over a wire and lends a different look to your build. It holds its shape and can be bent at tight angles without kinking. This hard line equals the following equivalent 1:1 size at each scale.1/25 scale =...