Engine Related

Dual Style Battery 1/25

A a pair of older style batteries with 2 long filler caps on the top. Shows a strap around the batteries and long filler caps with top posts.  Here is how to wire the batteries together.   1 resin piece, by Pegasus Hobbies, 1/25 scale...

Dual Quad Tunnel Ram Manifold 1/25

Set a pair of Dominator or Demon carbs on top of this manifold. Make sure you have room under your hood or cut a hole in the hood to allow for the height. Overall height is .43" (7/16"). Here's a photo of a real dual quad setup byRich Vitiritti. ...

Electric Fuel Pump & Filter 1/25

An electric fuel pump with a fuel filter similar to the MagnaFuel pump.     Here's a photo of the real thing     One resin piece, by Pro Tech, 1/25 scale.    

Spark Plug Wire Loom Set 1/25

A nice set of photo etched wire looms. Spreaders are in 2, 3 and 4-hole configurations. If using soft .020" (or smaller) rubber wires, use the looms as they are. If using solid wire, It is necessary to "clean up" the holes with a .020" bit so wires will...

Flowmaster Mufflers, Pair 1/25

A pair of nicely made and realistic looking offset inlet/outlet mufflers. These are 3D-printed with FLOWMASTER in raised letters on one side. Two 3D-printed muffler clamps and a Flowmaster decal is included for each muffler. Mount the muffler upside...

4-Pulley Set, 2-Grooves, 1/25

A set of four spun aluminum V-groove pulleys. Consists of: 1 Double groove crank pulley 1 Double groove water pump pulley 1 Large single groove accessory pulley 1 Small single groove accessory pulley Belt material   NOTE: The diagrams on the...

BBC Centered Motor Plate 1/25

A more accurate motor plate than found in a kit. It is designed for those cars with a centered driveline.While this motor plate is copied after the one used in the Revell Pro-Sportsman kits, it can be used in any build with possible modification.It is...

Soft Line Hollow Hose .105", 2.7mm OD

This a soft, hollow rubber line that is easily configured to the space you have. Dimensions: .105" OD .059" ID 12" Length This soft line equals the following equivalent 1:1 sizes:1/25 scale = 2-5/8"1/16 scale = 1-5/8"1/12 scale = 1-1/4"1/8 scale...

TurboCharger Plumbing and Wiring Schematics, 8-Pages

THIS IS A FREE DOWNLOADABLE PDF FILE. No purchase necessary. Want to add that extra detail to your turbo charged engine? Here is a set of diagrams that show the plumbing and wiring for a turbo charged system. Includes Waste Gate details along with...

Ferrule Fittings for Braided, Soft, Hard LInes -Silver

Perfect for simulating compression or crimp-type end-of-line fittings on NOS lines, blower injector lines, Injector-hat injection lines or carb fittings. Can also be used as radiator hose ends and carburetor 'boosters'.         ...

Turbo Charger Waste Gate, Pair 1/25

Making your own single or twin turbocharger setup? Here's something you need and it would be difficult to scratch build - waste gates.  Here's a pair of 3D-printed waste gates. A wastegate is a boost-controlling device that limits...

Pro Line 585 Blown 4000HP Dry Sump Engine 1/25

A 3D-printed BBC engine based on the Pro Line 4,000 HP 585 Billet engine. I designed it in Fusion 360 using photos of the real engine.   Engine block, large heads and Moroso oil pan are designed from the photo above. Injection distribution...