Wheels & Tires

Drag Slicks,17x36x16 1/25

These Drag Slicks equal a scale 17x36-16 tire.  This is representative of a current Pro Mod, FC or TF drag slick. Dimensions:Overall Width = .85"Diameter = 1.46"Tread Width = .70"Wheel Opening =.715" The tire ID is designed to work with earlier...

Tire Valve Stems 1/25

Add another element of detail to your wheels.A set of machined aluminum tire valve stems. Photo of Tire Valve Stems with .025 Hex Fittings for the lug nuts. Use .025 Evergreen rod for the studs. See the How-To article on detailing wheels:...

Dana - Narrowed Rear End & Brake Kit 1/25

Here is a complete Dana narrowed rear end with brakes. Overall with between axle tube ends is 1-7/8" Kit includes: Narrowed housing Rear cover Housing ends including one spare Resin brake hats Resin calipers PE drilled rotors PE...

Beadlock Rings, Weld 1/24

A set of 4 Weld Beadlock Rings for your rear wheels. The beadlock rings are die cast and silver in color. The rings are on a protective backing and I didn't want to peel one off, so these measurements might be slightly off but close enough. OD - ...

Wheelie Bar Housing Kit 1/25

Here is a Wheelie bar wheel housing kit designed for today's PM, FC, ADRL, SS, and others. Includes PE wheel housing and PE wheels which must be assembled. 3D-printed wheels are also included along with 2 pieces of telescoping rods and two hex pins...

Cragar 15" SuperTrick Wheels 4-Set, Hub 1/24

A highly detailed set of front and rear Cragar Super Trick wheelsThese Cragar's replicate 15" wheels used on 1970s-80s era drag cars.  Crowned centers are present on both front and rear wheels, with double-drilled pattern on rear wheels. Inner and...

CL's 19" Wheels & Tires 4-Set 1/24

A set of four chrome wheels with low profile tires. Sidewall and tread width is .45" (29/64") Like the wheels but don't want low profile tires?  Take these tires off and replace with other tires. All four wheels/tires are the same size (not big and...

Spindle Wheel Front Strut Kit, Slotted Rotors 1/25

This strut front end kit is made to accommodate spindle mounted wheels. The nose of the strut body is designed to center in the spindle cap and includes 3D-printed hubs to fit to the back side of the wheel. Also available is a Wishbone set that will...

5-Spoke 15" Wheel 4-Set, 1/24

A set of four 5-spoke 15" wheels and tires in a big 'n little configuration. The Yokohama soft tires come off easily so you can use your own. See the wheel dimensions below. Front tires have ADVAN HR-R in raised letters on sidewall along with 235/40VR...

Dragster Wire Wheels 20" 1/25

Finally, a wire wheel with real spokes that looks realistic and equal to a 20" wheel. Fully assembled and includes 3D-printed tires painted Tamiya TS-82 "Rubber Black". Featuring small hubs and thin-walled rims for a proportional appearance. The...

Firestone Champion Front Tires, 1/25

These narrow front tires will work for a Gasser as well as a street racer. Has Firestone in raised letters on sidewall (one side only). Soft pliable rubber. Contains a little 'flash' which is easily removed. Measurements: Outside Diameter = .1...

Mud Flaps or Anti-Sail Weights 4-Pair 1/24-1/25

A set of photo etched weights to keep big rig mud flats from sailing. Can also be mounted behind pickup rear tires. Contains enough for 8 wheels. They can be painted or left 'bare' for that aluminum or chrome look.   By Detail Master, 1/25...