Fuel Management

Soft Clear Line - Hose .039, 1mm OD

This is a soft, clear line that bends easily and smoothly.  It's able to bend at a sharp angle without kinking. See .040" Hex Fittings or Size C (or Size D for more space) Ferrules for hose ends.This clear line equals the following equivalent 1:1...

Flathead Finned Oil Filter 1/25

An external machined aluminum finned oil filter for a Flathead Ford engine. Included are vinyl and aluminum lines for the inlet and outlet plumbing of the filter. A diagram and directions are printed on the back of the header card. Here is an accessory...

Single Barrel/Flathead Air Cleaners 1/25

Three small machined aluminum air cleaners. Although these are single barrel air cleaners, they're also made to fit atop the Flathead Oil Filter by Parts by Parks Three aluminum pieces by Parts by Parks, 1/25 scale.

3-Hole Tri-Power Scoop, Short 1/25

A 3-hole scoop/hat in a triangular shape. Overall length is 1" A longer version of this scoop is also available.   2 resin pieces by VCG Resins, 1/25 scale.    

Tunnel Ram Kit 1/25

Two Dominator carbs on a tunnel ram manifold.   Six pieces, resin, by VCG Resins, 1/25 scale.    

Gray Cable .010", .25mm Dia

This looks like a stainless steel line, but it's a small gauge stainless steel wire wrapped in a gray nylon jacket. This is ideal for a throttle or parachute release cable where a steel cable is housed in a jacket. The wire core is springy and doesn't...

Carburetor Detail Set 1/24-1/25

A photo etched sheet of detail parts for your carb. Includes, base plates, throttle linkage, annular boosters and throttle linkage connection pivot plates.   By Detail Master, 1/24-1/25 scales.

Velocity Stacks, 4bbl Carb 1/24-1/25

Really nice looking aluminum velocity stacks for that 4bbl carburetor. Pack contains 2 stacks, turned solid aluminum, so there's no seam. They are hollow, so you can see the carb butterflies. Outside diameter at the carburetor junction is 1/4", 6...

Carbon Fiber Style Hat, Long 1/24

A round 3-hole hat that is typically seen in carbon fiber. This is a long version.  A shorter version is also available. Molded in one piece. 1/24 scale, by Competition Resins.

PSI Blower 1/25

A PSI Blower in one-piece resin.For a 'roots' type blower, see the Kalbelco series of 671, 1471 and 1671 super chargers. This is a standalone blower - pulleys or other components are not included. Contains 1 resin blower by Competition Resins, 1/25 scale.

Carbon Fiber Style Hat, Short 1/24

A round 3-hole hat that is typically seen in carbon fiber. This is a short version.  A longer version is also available. Molded in one piece. 1/24 scale, by Competition Resins.

Cross-Ram Manifold & Carbs 1/25

A cross-ram & carburetor package.All items have locating pins for easy alignment. Consistis of: 1 Cross-Ram manifold 2 4bbl carbs 1 Air cleaner   1/25 scale by Competition Resins

1471 Kobelco Blower with Blanket 1/25

A Kobelco 1471 Blower with a restraint blanket molded in.Made in one piece.This a blower only - pulleys or other components are not included. Check out this photo for an idea of which blower you need. Contains 1 resin blower.

Pro Stock Style Fuel Cell 1/25

A Pro Stock type Fuel Cell. Contains 1 resin tank, 1/25 scale

Dual Nitrous , O2, Fire or Air Bottle Pair 1/25

Here are a pair of bottles that can be used for nitrous, fire, compressed air, oxygen, etc. Mount them in the interior, at the rear or ahead of the engine. Add a NOS decal found here, if this is the intended use for these bottles.  The 'small' size...

1471 Kobelco Blower 1/25

A 1471 Kobelco Blower in one-piece resin.The detail is quite good and the bolts are sharp. This is a standalone blower - pulleys or other components are not included. Check out this photo for an idea of which blower you need. Contains 1 resin blower.

Fuel or Brake Hard Line .020, .52mm Dia

This solid aluminum line is soft to bend and will not kink, even at tight angles. It straightens out easily and will conform to any shape you want.This aluminum 'hard' line equals the following equivalent 1:1 size at each scale.1/25 scale = 1/2"1/16...