Shop by Manufacturer

GM Lap Seat Belts with PE Buckles 1/25

A set of 4 authentic looking lap seat belts with excellent photo etched buckles. Excellent addition to a muscle car, hot rod, rat rod or other early vehicle. Belt material has the same weave texture as a real seat  belt and the PE buckles are thin...

Weld Magnum Front Wheels 1/25

A pair of Weld Magnum front wheels.Includes: Outer Rims Inner and Outer Center Inserts Hubs Instructions A Front Strut spindle kit is available for these wheels.  The nose of the spindle is designed to center in the spindle cap and...

Soft Line - Hose .005", .12mm OD

This is the smallest black soft line I have. This is a shiny black nylon line. It is slightly springy and can be bent at sharp anglesThe OD dimension is .0047" or .14mm.  Typical uses are small oil lines, vacuum and fuel lines, especially fuel...

Ford Boss 429 & Lenco 1/25

An all new, highly detailed, complete 429cid Ford engine with the Boss 429 cylinder head/valve cover combo. Perfect for that '80s to '90s Pro Stock racer. Included is everything needed to build a well detailed, carbureted engine with a 4-speed...

3D-Printed 'Street' 4bbl Carburetor 1/25

Highly detailed Holley Street 4-bbl Carburetor with a choke plate in the closed position.With single or dual carbs, you'll need a Fuel Junction Block (see 1/25 SCALE/ENGINE RELATED/FUEL MANAGEMENT). Also see the Braided Lines, Hard Lines, Soft Lines and...

Brake Kit - Rear, Drilled Rotor .125" Spindle Diameter 1/25

This is the same rear end brake set as Futurattraction's FA-C-ROT-DR2R-063, except this rotor has a larger .125" ID hole. This allows for the hubs and rotors to slide over Futurattraction's axle housing and gives more gluing surface where they are...

Radiator or Heater Hose, .070" OD

This solid core wire is used as a 1-3/4" radiator hose or other larger transfer hose at 1/25 scale.  At 1/16 scale it equals a 1" diameter hose, which is closer to a heater hose. It has an outside diameter of .070" It will hold its shape when...

Flowmaster Mufflers, Pair 1/25

A pair of nicely made and realistic looking offset inlet/outlet mufflers. These are 3D-printed with FLOWMASTER in raised letters on one side. Two 3D-printed muffler clamps and a Flowmaster decal is included for each muffler. Mount the muffler upside...

HEMI Injector Manifold 1/25

A fuel injector manifold for your HEMI engine.   Here's a fuel plumbing diagram for this manifold.The lines go to a distribution block in the center.      Velocity stacks are available to fit this manifold. File the little 'nubs' on...

Throttle Linkage Set, 1/25

A throttle linkage set with pins added to the ends of the linkage components. This will provide a more stable attachment point for linkage rods, etc. Depending on your attachment, the pin may have to be bent 90 degrees.   Photo etched...

NoS or Fire Aluminum Bottle Set with Bracket 1/25

You won't find a more realistic nitrous oxide bottle than this one.  Use one for a fire bottle if you have a fire suppression system plumbed. (The parts photo shows resin bottles and valve, but the bottle is aluminum, and the valve is...

Hub Wheel Front Strut Kit, Slotted Rotors 1/25

This strut front end kit is made to accommodate 5-bolt, hub mounted wheels. The nose of the strut body is designed to center in the spindle cap and includes 3D-printed hubs to fit to the back side of the wheel. Also available is a Wishbone set that...